MOTOR, M3AA112 MB-2 6.4KW 3440RPM 3-PHAS SQUIRREL CAGE INDUCTION MOTOR
The single phase voltage in the Middle East, GCC and some parts of Europe is 220 V +/- 10%, so engineer Bilal was right
The required colour for item 14 is red
The Level of poles for item 20 is 3P + N ( But usually the unit is supposed to be capable of being configured for all given options)
ADS551 low level dissolved oxygen sensor assembly, Part#:AW502 080, Make: ABB, User: I&C
Flowmeter assembly, Part#:AW502 060, Make: ABB, User:I&C
Sample outlet pipe - flowmeter fitted, Part#: AW502 066,Make: ABB, User:I&C
Qd connector kit including elbow, Part#:AW502 061,Make: ABB, User:I&C
Sensor cable assembly, Part#:AW502 081, Make: ABB, User:I&C
Drain valve assembly including bonded seal, Part#: AW502 056, Make: ABB, User:I&C
Conductivity Board, Part#: AX400/0265, Make: ABB, User:I&C
Dual Channel Process water Conductivity Analyzer, Model AX400, Make: ABB, User: I&C
No. 3RN2010-1BW30 without ATEX
1UNIT HORIZONTAL GEARBOX CYCLO DRIVE
Model : Cyclodrive
Power : 37 kW
Ratio : 1/29
Input speed : 1450 Rpm
SF : > 1,5
Input / output shaft : solid shaft with key ways
Type : Cyclo
Power : 7,5kW
Ratio : 1/59 or 1/60
SF : 2.0
Input speed : 1500 Rpm
Output speed : 24-25 Rpm
Diameter shaft output : Dia. 95 mm
Electromotor
Power : 7,5kW/4P/3Ph/380V/660V/50Hz
Insulation Class : IP 55/F
Crawler driven motor BWD – 29 – Quantity: 1 pcs.
Motor Siemens 1TL0001 – 1AB5 – 3KW EFF 85.5 % COS 0.79 – Quantity: 1 pcs.
Motor cycloid BWY 22 – Quantity: 1 pcs.
Motor sumitomo TK – FCX – Công suất 7.5 Kw – 4 Phase – Quantity: 1 pcs.
Motor Siemens 1TL0001 – 1DB2 – 11 Kw – 160M – EF 89.8% - Cos 0.84 – Quantity: 2 pcs.
Motor cycloid BWD4 - 23 – Quantity: 1 pcs.
Vacuum Fan Motor 4-72 wuxi shengjia (Speeed: 2900 rpm) – Quantity: 1 pcs.
Motor Siemens 1TL0001 – 1DA3 – 15 Kw – 160M – EF 91.3% - Cos 0.86 – Quantity: 2 pcs.
Motor Siemens 1TL0001 – 1AB4 – 2,2 Kw – 100L – EF 84.3% - Cos 0.79
Crawler driven motor BWED 41 - 121 – Quantity: 1 pcs.
MOTOR, M3AA112 MB-2 6.4KW 3440RPM 3-PHAS SQUIRREL CAGE INDUCTION MOTOR
PLE80 servo motor planetary gearbox
ratio 40:1
400W AC servo motor
For the gearbox with motor power 0.75kW, the Service Factor (Safety Factor) is 3.95.
For the gearbox with motor power 1.5kW, the Service Factor (Safety Factor) is 1.95.
the gear box of BWY18-29-0.75Kw and the gear box of BWY18-29-1.5Kw
UNT -- INDUCTION MOTOR, 0.4KW 1750RPM 440V 3PHA
SQUIRREL CAGE INDUCTION MOTOR
Brand: ABB/Siemens/WEG/SEW
0.4 kw, 440 volts, 60 hz, 3-phase
RPM: 1750 rpm
Degree of Protection: IP55
Insulation Class: F
Mounting Type: IMB3 Foot-Mounted Type
1UNIT CYCLO VERTICAL GEARMOTOR
Type : Cyclo
Power : 7,5kW
Ratio : 1/59 or 1/60
SF : 2.0
Input speed : 1500 Rpm
Output speed : 24-25 Rpm
Diameter shaft output : Dia. 95 mm
Electromotor
Power : 7,5kW/4P/3Ph/380V/660V/50Hz
Insulation Class : IP 55/F
Motor Siemens 1TL0001 – 1AB5 – 3KW EFF 85.5 % COS 0.79
Motor Siemens 1TL0001 – 1DA3 – 15 Kw – 160M – EF 91.3% - Cos 0.86
Explosion-proof asynchronous electric motor of two-speed type DAKV (AVK) 30 / 15-4 / 8U5;
power: 30 / 15kW; network voltage - 660V;
rotation speed - 1500/750 rpm;rated current 33.5 / 26.0 A. 1pieces
ELECTRIC MOTOR Detailed description:
Three-speed asynchronous explosion-proof electric motor DATV (AVT) 15-4 / 6 / 12U5;
power: 22/46/23 kW; network voltage - 660V; rotation speed - 1500/1000/750 rpm;
rated current -26.5 / 56.5 / 48 A. 2 pieces
Gearbox
P = 2.800 kW
n1 = 800 - 1.300 min-1
iNout1 = 54/64: 1
iNout2 = 43/64: 1
The multiplier is lubricated at a pressure of 3.5 -filtration of oil 20 µm.
The multiplier grease shall effectively lubricate and cool the multiplier assemblies and bearings, operating temperature of the assemblies and bearings shall not exceed 45°C.
The design of the grease supply to the bearings should ensure constant control of the grease supply.
Mounted rolling bearings must have an initial clearance of max. 0.02 mm.
Degree of accuracy according to GOST 1643-81 8-V.
Parts should be made of 18Х2Н4МА steel.
The working surfaces of the teeth to cement h 1.1-1.5 mm. 57...63 HRC.
Shafts 197...269 HB.
Roughness of surfaces 1,6.
Nodes to be balanced.
Item 32
Voltage rating: 0 – 137.5 VAC
Scale: 0 – 750
Legend AC VOLTS
Item 33
Specification:
*Model: LW38D-16/
*Positions: 3
*Terminals: 8
*Ui: 5500V ; Ith: 16A
*Action Type: Latching
*Positioning angle: 60-0-60 Degree
*Mounting Type: Plate, Screw
*Mounting Hole Distance: 36mm x 36mm / 1.41inch x 1.41inch (L*W)
*Overall Size: 49 x 49 x 71mm / 1.93 x 1.93 x .8inch (L*W*H)
*Rating: DC-13: Ui: 0V , Ith: 0.A ; AC-: Ue / Ie: 380V / 1.5A
7.5 kw 10 hp 3 phase electric motor
2UNT-- MOTOR, M3AA112 MB-2 6.4KW 3440RPM 3-PHAS
SQUIRREL CAGE INDUCTION MOTOR
Brand: ABB Motors
Model: M3AA112 MB-2
6.4kw, 440 volts, 60 hz, 3-phase
RPM: 3440 rpm
Degree of Protection: IP55
Insulation Class: F
Mounting Type: IMB5 Flange Type
Cast-iron Motor Frame
one unit - Brand New 7.5Hp (5.5kw) ABB Electric Motor, Type M2QA 132 S4A,
Horizontal Foot Mounted, 3Phase, 60Hz., 220 volts, AC, 1800 rpm (4pole),
1.15 Service Factor, Class F Insulation, IP 55 Protection, Cast Iron Body& Base, TEFC.
note that Item 124 – current transformer,
The MFG is Acrel, The ratio is 5000/1/voltage-0.66/3/kv/frequency 50/60 hz, the MFG part number is BAY66 150*50
Reducer: Skoda type:570-078; portable ratio i=20; power 250 kW, n₁=1480 min⁻¹
Hydro-coupling with variable pumping, type: R 630 B ; power 250-400 kW,
The connection between the hydro-coupling and the reducer is with periflex rubber 10-512 with diameter 402 mm.
Reducer: FLENDER type:B3 DH 11A; portable ratio n1 = 1480 min-1, n2 = 74,45 min-1, ; power 250 kW,
Hydro-coupling turbo with constant charging VOITH type: 562 TVVS C; power 117 kW, n1 = 1480 min-1,
The connection between the hydro-coupling and the reducer,
and between the electric motor and the hydro coupling is with coupling GPK-X 630.
The MFG is Acrel, The ratio is 5000/1/voltage-0.66/3/kv/frequency 50/60 hz, the MFG part number is BAY66 150*50
All items delivered for tender number HFY-PUR/PD1036-1023
Gear Motor Coupled
Power: 15 KW, Motor RPM based on 1450
Ratio: 1:12
Foot mounted, Safety Factor 1.5~2
Gear Motor Coupled
Power: 15 KW, Motor RPM based on 1450
Ratio: 1:32
Foot mounted, Safety Factor 1.5~2
Gear Motor Coupled
Power: 22 KW, Motor RPM based on 1450
Ratio: 1:32
Foot mounted, Safety Factor 1.5~2
MOTOR, M3AA112 MB-2 6.4KW 3440RPM 3-PHAS SQUIRREL CAGE INDUCTION MOTOR
Gear Motor Coupled
Power: 30 KW, Motor RPM based on 1450
Ratio: 1:32
Foot mounted, Safety Factor 1.5~2
Reduction Gear
Power: 50 KW, Motor RPM based on 1450
Ratio: 1:30
Foot mounted, Safety Factor 1.5~2
Reduction Gear
Power: 35 KW, Motor RPM based on 1450
Ratio: 1:30
Foot mounted, Safety Factor 1.5~2
Reduction Gear
Power: 35 KW, Motor RPM based on 1450
Ratio: 1:32
Foot mounted, Safety Factor 1.5~2
VFD KEYPAD FBG11B SEW EURODRIVE 5 PC
2 UNT - CAGED MOTOR, 0.8KW 900/0.33RPM 254/440V
SQUIRREL CAGED INDUCTION MOTOR
Brand: SEW Eurodrive
Model: SA62R43MT80N8
0.8 kw, 254/440 volts, 60 hz, 3-phase
RPM: 900/0.33
Degree of Protection: IP55
Insulation Class: F
Mounting Type: IMB5 Flange-mounted type
2UNT -- CAGED MOTOR, 0.55KW 1660/45RPM 440V 3PHA
SQUIRREL CAGED INDUCTION MOTOR
Brand: SEW Eurodrive
Model: RF37DT80K4
0.55 kw, 440 volts, 60 hz, 3-phase
RPM: 1660/45
Degree of Protection: IP55
Insulation Class: F
Mounting Type: IMB5 Flange-mounted type
Delivery and Commissioing of Pre-wired LVSG, 480V, 60Hz, 3pole, 60kAIC, IP54 Enclosure, Free Standing, GA #14,
Bottom Entry, Control trans and CT for metering, Profibus DP Ready Energy Meter, with grounding bus bar,
extesion bus bars for incoming and out-going power cables, w/ 1kV shrinkable rubberized tube insulator, Exhaust fan, finished in wrinkle light gray powder coated RAL 7035.
Suitable for 518kW, 760Amp, 440V, 60Hz Compressor.
1 - Main - ABB MCCB -Tmax T7S16003P ELSIG w/ Aux. contact
1 - ABB Soft Starter with External By-pass contactor (700-800kW)
1 - ABB Thermal Overload
1 - Vacuum Contactor ABB/Siemens
1 - Energy Meter Profibus DP ready
1 - Current Tranducer 230V input, 5Amp input, 4-20mA output
7 - relays 230vac, 60Hz
3- LED indicator for breaker status (on, off, trip)
4 - LED indicator for softstarter status (start, by-pass/run, stop, trip/fault)
1 - 2 pole MCB 4Amp
Delivery and Commissioing of Pre-wired LVSG, 480V, 60Hz, 3pole, 60kAIC, IP54 Enclosure, Free Standing, GA #14,
Bottom Entry, Control trans and CT for metering, Profibus DP Ready Energy Meter, with grounding bus bar,
extesion bus bars for incoming and out-going power cables, w/ 1kV shrinkable rubberized tube insulator, Exhaust fan, finished in wrinkle light gray powder coated RAL 7035.
Suitable for 230kW, 370Amp, 440V, 60Hz Pneumatic Pump.1 - Main - ABB MCCB -Tmax T6S8003PELS/I w/ Aux.
1 - ABB Soft Starter with External By-pass contactor
1 - ABB Thermal Overload
1 - Vacuum Contactor ABB/Siemens
1 - Energy Meter Profibus DP ready
1 - Current Tranducer 230V input, 5Amp input, 4-20mA output
7 - Relays 230vac, 60Hz
3 - LED indicator for breaker status (on, off, trip)
4 - LED indicator for softstarter status (start, by-pass/run, stop, trip/fault)
1 - 2 pole MCB 4Amp
I wanted to have the price of a 220/380 three-phase electric motor with reducer gearbox. speed input about 1500 rpm output about 300 rpm.
I’m interested in your product 7.5 kw 10 hp 3 phase electric motor with aluminium housing,
2UNT--- INDUCTION MOTOR, 6.6KW 1755RPM 440V 3PHA
SQUIRREL CAGE INDUCTION MOTOR
Brand: Siemens
Model: 1LA71304AA60-Z
6.6 kw, 440 volts,60 hz, 3-phase
RPM: 1755 rpm
Degree of Protection: IP55
Insulation Class: F
Mounting Type: IMB3 Foot-mounted Type
Tank you for your answer, I would like a 220 volt 60 HZ mono engine about 1500 rpm with a gearbox of 300 rpm.
These are flange type og shaft
Ee need for bully type
Quantity eill be ss follows
7.5 hp 100 unit
5.5 hp 50 unite
3 . 10 . 15 hp .... alk 30 pcs
coupling JN460 - 1psc. - Y4-2x73NO34.5F F11103-1011793/F103078
A10VSO 71 - 1 unit.
A10VO45 - 1 UNIT
A10VO100 - 1 UNIT
A10VO140 - 1 UNIT.
Item 32
Voltage rating: 0 – 137.5 VAC
Scale: 0 – 750
Legend AC VOLTS
Item 33
Specification:
*Model: LW38D-16/
*Positions: 3
*Terminals: 8
*Ui: 5500V ; Ith: 16A
*Action Type: Latching
*Positioning angle: 60-0-60 Degree
*Mounting Type: Plate, Screw
*Mounting Hole Distance: 36mm x 36mm / 1.41inch x 1.41inch (L*W)
*Overall Size: 49 x 49 x 71mm / 1.93 x 1.93 x .8inch (L*W*H)
*Rating: DC-13: Ui: 0V , Ith: 0.A ; AC-: Ue / Ie: 380V / 1.5A
Tank you for your answer, I would like a 220 volt 60 HZ mono engine about 1500 rpm with a gearbox of 300 rpm.
3 HP 30 MOTOR ( CONNECTION BOX ON RIGHT SIDE )
5.5 HP 30 MOTOR ( CONNECTION BOX ON RIGHT SIDE )
7.5 HP 150 MOTOR ( CONNECTION BOX ON RIGHT SIDE )
10 HP 30 MOTOR ( CONNECTION BOX ON RIGHT SIDE )
15 HP 20 MOTOR ( CONNECTION BOX ON TOP SIDE )
ALL IP 55 CLASS F , ETC , IE3 ,
ALL SHOULD BE 230/380 VOLT , 60/50 HZ
My project is to run my generator of 10 kw 300 RMP
I would like a 220 volt 60 HZ mono engine about 1500 rpm with a gearbox of 300 rpm.
Helical geared motor 0.75kW , n2=15-20rpm, base foot, factor >1 – 1 sets
Helical bevel geared motor 5.5kW, n2=75-80rpm, base foot, hollow shaft, factor >1 – 1 sets
Helical bevel geared motor 7.5kW, n2=75-80rpm, base foot, hollow shaft, factor >1 – 1 sets
My project is to have an engine that runs at 1500 rmp 2 amps in three phase with a speed reducer for 300 rmp.
2 UNT -- INDUCTION MOTOR, 65KW 1778RPM 440V 3P
INDUCTION MOTOR
OCV3252B
1LEO1032CB23-4AA4
65 kw, 440 volts, 95 amp, 3-phase
1778 rpm
Foot Mounted w/ Grease Fittings and Discharge
IE2 Compliant
Shaft Diameter: 65mm
Supply, Delivery and Commissioing of Pre-wired LVSG, 480V, 60Hz, 3pole, 60kAIC, IP54 Enclosure,
Free Standing, GA #14, Bottom Entry, Control trans and CT for metering,Profibus DP Ready Energy Meter,
with grounding bus bar,extension bus bars for incoming and out-going power cables, w/ 1kV shrinkable rubberized tube insulator,
Exhaust fan, finished in wrinkle light gray powder coatedRAL 7035. Suitable for 518kW, 760Amp, 440V, 60Hz Compressor.
1 - Main - ABB MCCB -Tmax T7S16003P ELSIG w/ Aux.contact
1 - ABB Soft Starter with External By-pass contactor(700-800kW)
1 - ABB Thermal Overload1 - Vacuum Contactor ABB/Siemens
1 - Energy Meter Profibus DP ready
1 - Current Transducer 230V input, 5Amp input, 4-20mA utput
7 - relays 230vac, 60Hz
3 - LED indicator for breaker status (on, off, trip)
4 - LED indicator for soft starter status (start, by-pass/run, stop, trip/fault)
1 - 2 pole MCB 4Amp
Supply, Delivery and Commissioing of Pre-wired LVSG, 480V, 60Hz, 3pole, 60kAIC, IP54 Enclosure, Free Standing, GA #14,
Bottom Entry, Control trans and CT for metering,Profibus DP Ready Energy Meter, with grounding bus bar,extension bus bars for incoming and out-going power cables, w/ 1kV shrinkable rubberized tube insulator,
Exhaust fan, finished in wrinkle light gray powder coated RAL 7035. Suitable for 230kW, 370Amp, 440V, 60Hz Pneumatic Pump.
1 - Main - ABB MCCB -Tmax T6S8003PELS/I w/ Aux. contact
1 - ABB Soft Starter with External By-pass contactor
1 - ABB Thermal Overload
1 - Vacuum Contactor ABB/Siemens
1 - Energy Meter Profibus DP ready
1 - Current Tranducer 230V input, 5Amp input, 4-20mA output
7 - Relays 230vac, 60Hz
3 - LED indicator for breaker status (on, off, trip)
4 - LED indicator for softstarter status (start, by-pass/run, stop, trip/fault)
1 - 2 pole MCB 4Amp
1 pc ABB MCCB -Tmax T7S16003P ELSIG
1 pc ABB MCCB -Tmax T6S8003PELS/I
Only the BLD2 1\59 reducer is needed (see attachment). The weight of the reducer is 40 kilograms +\-!
01 gearbox FDAF108B-K4-(90) ratio 168.88/1
1.GEARBOX, FOR MOTOR GRINDER
BOTTOM ASH,TYPE HORIZONTAL PINWHEEL
CYCLOIDAL, STAGE: ONE STAGE, MOUNTED:
FOOT MOUNTED, RATIO: 1 : 3.4, INPUT RPM:
1371, D:80, D1: 40, REF: XW-8185,
DRAWING ATTACHED
qty : 1 set
Can you send me the price of a 1500 rmp motor with a 300 rmp gearbox.
I need industrial electric motor power from 30 HP 1400 and 3000 till 300 HP
Is XW-8185 available in 1 set?
(GEARBOX, FOR MOTOR GRINDER BOTTOM ASH,TYPE HORIZONTAL PINWHEEL CYCLOIDAL,
STAGE: ONE STAGE, MOUNTED: FOOT MOUNTED, RATIO: 1 : 3.4, INPUT RPM:1371, D:80, D1: 40)
Can you send me another quote with a 1500 rmp motor of 5kw 300 rmp out in 50 / 60hz.
Almotafauiqa Trading FZCO.
UAE - Dubai
1 SET GEARBOX FOR MOTOR GRINDER BOTTOM ASH, TYPE HORIZONTAL PINWHEEL CYCLOIDAL, STAGE, ONE STAGE MOUNTED,FOOT MOUNTED, RATIO 1:3.4 INPUT RPM 1371, D:80, D1:40, REFF : XW-8185, DRAWING ATTACH
1 SET FLUID COUPLING FOR MOTOR GRINDER BOTTOM ASH, TYPE CONSTANT FIILING FLUID COUPLING D:345 MM, D1:38MM,D2:40MM, OIL FILL : 1.4-2.8 LITRE OIL:ISO VG-68, REFF : YOX280A, DRAWING ATTACH
1 SET ROTARY FEEDER, FOR BUCKET ELEVATOR BOTTOM ASH, DIMENSION : A1:410MM, B1:365MM, C1:300MM, H:450MM, E:800MM, REFF : XG-100T/H,WUXI SHENQUAN POWER EQUIPMENT CO.,LTD
Brand: ABB
65kW,1784rpm,440V,IP55,Class F,IE3,Self Ventilated Cooling System,
Type:M3BP250SMB4
INDUCTION MOTOR, 65KW 1778RPM 440V 3P
OCV3252B , 1LEO1032CB23-4AA465 kw, 440 volts, 95 amp, 3-phase 1778 rpm
Foot Mounted w/ Grease Fittings and Discharge IE2 Compliant Shaft Diameter: 65mm
Qty : 3 Each
ASSEMBLY,MAIN PCB, 4600/0248
PRODUCT ID : 4600/0248
DESCRIPTION : WALL MOUNTED MAIN PCB ASSY (CONTAINS PSU)
MANUFACTURER : ABB
